Is your DirecTV remote control having trouble controlling the volume? The post you’re looking for is here. It may be possible to use your remote control with both your TV and your DVR box for functions such as changing channels, muting, changing inputs, etc. Unfortunately, the volume control doesn’t work.
Here are four simple steps to fix the DirecTV remote volume not working error.
This issue can be attributed to a couple of reasons. There are some errors we need to fix as soon as possible.
What is the problem with my DirecTV remote volume?
- You need to check whether the TV/DVR box is connected to the remote
- The batteries are flat and you’re using them
- Programming of the remote will not be successful
- Remote control partially programmed
- There is a problem with the speaker on your TV
- Connection of the audio cable should be checked
- The volume button has been a source of complaints
- Your remote model number was incorrect when you paired it
What is the solution to DirecTV’s volume control problem?
Your methods, such as unblocking the remotes, replacing batteries, etc., were already tested. In order to avoid going through those steps again.
DirecTV remotes don’t pair properly with DVR boxes and TVs, and this is one of the most common problems. Partial pairing is also possible.
It is likely that you are using the wrong device code, which causes the errors in pairing.
In order to resolve this issue, I have the following recommendation.
If you don’t see the TV mode button on the top button, make sure it is set to TV mode before moving on.
Reset the remote control
This project mainly consists of reprogramming the remote control for the TV and our DVR receiver. Consequently, we do not wish to show the volume control issues again. The DirecTV remote control will be reset before being reprogrammed again using the intact device code in order to minimize any types of errors.
How to reset it?
When the indicator blinks twice, press and hold both the mute and select buttons. When the indicator light blinks four times, enter the reset code 981. That’s all.
Make sure the exact code is programmed into the remote and the box
Both your receiver and TV must be paired with the remote.
To begin with, you should connect the TV to the receiver and all the necessary connections.
Two methods are available for controlling streaming content from DirecTV satellite. Depending on whether the DVR is connected to the TV or to the receiver. You should pair your TV with the DirecTV remote control properly, using the correct device code, if you plan to do away with the original TV remote.
Your TV’s brand and the remote model may determine the device codes. There are different codes for each brand.
To get the code, Visit this official link https://www.directv.com/DTVAPP/content/remote_codes2
The remote model number can be found by clicking on it, then the TV can be selected. The device code is a 5-digit code and can be obtained by selecting the TV brand from the box. It will be easier to avoid partial pairing issues if we get the correct code.
To program the remote, follow these steps
- The indicator light will blink twice when you press and hold the Mute and Selection button.
- You can then use the keypad to enter the exact code for the device
- Two flashes will be seen on the green indicator light
- Make sure the volume button on your remote is working by pointing it at the TV
Recheck the cable & connections
In order to fix volume issues with the DirecTV remote control, the DVR and TV must be connected properly.
It won’t be possible to control the TV volume if there is no audio output provided to it.
Ensure that the COAX and HDMI cables, as well as the power cord, are properly connected.
Verify that the HDMI cable is in good working order. To establish a connection between the box and the TV, you can replace the HDMI cable with another one that is new at home. Because HDMI cables connect your TV to your sound and picture systems.
Check the volume button
In the case that only the volume control button is not working, but that the power button, channel change buttons, mute button, etc, are all working fine, the problem is most likely a volume control button issue.
Press the button and check the indicator light to see if it is working properly. It is easy to confirm that the key is working when you press the button and the indicator light blinks.
In this method, also make sure that all other buttons work.
Buying a new replacement remote or repairing the volume button are options if the button does not work.
Apply conductive electric paint
In view of the fact that every other button is working fine, you can be assured that there is no problem with the circuit board. An eraser can be used to remove the conductive electric paint from the button mat. In order to repair this, you need to remove the button mat/membrane from the body panel. Once you have found the volume button, press it.
On the bottom side of the button, apply the conductive electric paint gently. Once it has dried, allow it to sit for a few minutes. Try the volume key again after reassembling the button mat and remote body.
Check whether the TV Volume button is stuck or not
You should check the volume button on your TV whether is stuck on the panel. If it is stuck, the volume on the remote won’t work. Press and release the button continuously and get it into the actual state.
Then try the volume key on the remote to check whether it is working or not.
Buy a remote control
The DirecTV remote control should be replaced if you have exhausted all troubleshooting methods and have found no issue with the TV, DirecTV DVR box, etc. A trusted dealer or the official website are the best places to buy it.
Bringing your neighbor’s remote control, who used the DirecTV satellite box, will allow you to confirm the problem.
Conclusion
There is nothing more frustrating than not being able to control the volume of the TV. By sliding the top button on the DirecTV remote, you can change the remote control’s mode to the TV, if you have it programmed to your TV using the Genie remote.