The following tips will help you fix your GE universal remote when it stops working. A few common remote control problems will also be discussed. There are some glitches being experienced by people. Getting the remote back into good working order can be done in a couple of ways.
Some common problems are
- The volume button is not working
- There is a problem with the menu button on the GE remote
- A continuously flashing power button
- Taking a long time to respond to the device
- The channel buttons do not work
- The GE remote cannot be programmed, etc.
What should I do if the GE universal remote does not work?
Follow these troubleshooting steps
Batteries should be checked
To begin with, you should check the batteries in the GE remote. When the batteries on your remote run out, your device will not function. The remote does not have a battery status indicator, so you should replace them.
When changing batteries, make sure both are replaced. Make sure the positive and negative terminals are aligned with their corresponding slots in the battery compartment.
Test whether the IR sensor is working fine
The next step is to verify that the IR sensor on your remote is working properly. You may know a simple trick that will help you learn this. Go to your smartphone’s camera app and open it. Press all the buttons on the remote control after pointing it at the camera. Every time you press a key, the IR LED will blink when the IR sensor is working properly.
To check if the buttons are functioning properly, follow this simple procedure. There have been many reports that the volume, channels, and menu buttons on the GE remote aren’t working. A possible way to determine if the problem lies with a specific button is to do this test.
Move from the shift mode
You may not be able to use the remote when it is in shift mode. The remote must be programmed to the correct device code immediately after leaving the shift mode.
Changing modes is as easy as pressing and releasing the shift or setup button. The LED light will blink once you have done so. After you have pressed the arrow keys, remove the batteries for two minutes after the LED light has stopped blinking. It needs to be re-inserted and then reprogrammed.
Reset your remote control
The following troubleshooting tips are somewhat outdated. All saved settings and data will be lost if the remote is reset to factory settings. There will be a resolution to any issues related to the programming or code applied.
I suggest that you perform a power recycle before you get a hard reset. You have to remove the batteries from the remote a couple times, then program the code (the 4-digit code can be found on their official website). In the event that this does not work, you can perform a hard reset.
Also Read: Why Is Onn Roku TV Remote Not Working? [Updated Guide]
Reprogram the remote
The GE universal remote needs to be reprogrammed with the correct 4-digit codes after being reset. GE remotes may not work the way you want if the right code isn’t used. The remote may be partially programmed when you don’t use the correct code.
It is important to check the CL version of the remote when finding the correct GE universal remote code for your device. On the official website, you will find the appropriate code.
There will be a list of codes you need to enter. The first code on the list should be used. GE universal remotes can be programmed without the code, but I strongly advise you to use the code.
Fixing hardware-related issues
There is an issue with the hardware part of the GE universal remote that results in the Volume, Power, and Channel buttons not working.
A remote control will have issues related to prolonged use if you use it for a long time. In order to determine whether the remote control has a stuck button, you should check all the buttons on the remote control. Each and every button needs to be pressed and released rapidly in order to unstick.
Some GE remote buttons are not working – Fixed
It is usually the remote control button mat or membrane that causes some buttons or keys not to function. Electric paint on the membrane of the buttons may wear off after prolonged use, preventing communication between the keys and the circuit board. The button mat must be removed from the remote panel before this can be fixed.
In order to remove all dust particles that have accumulated on the mat, clean it with a brush.
Simply use a cotton cloth to clean the circuit board as well as the button mat with Isopropyl rubbing alcohol that you have at home. According to the nature of my business, I use MySpirit Isopropyl rubbing alcohol for various circuit board cleaning tasks.
Apply electric paint
You can enhance the functioning of remote control buttons by applying electric paint, which is a conductive metallic liquid.
Make sure the button mat on the remote control does not show any signs of degrading.
Buying conductive electric paint and using it gently on the buttons’ downsides will solve this problem. It can either be applied directly from the tube or with earbuds.
It is important to wait for a few minutes after applying this conductive electric paint to ensure that it is completely dry. Place the button membrane and circuit board in the correct positions to reassemble the remote control.
Cost-effective General Electric Universal remote
If the problem is with the circuit board, it would be difficult to fix. The best solution is to buy a new remote instead of taking it to a technician.
Users of GE remotes know how cheap they are. Buying a new remote control that controls multiple devices costs less than $10. GE remote controls are cheap, so if it can’t be fixed, just buy a new one. With the new remote pack, you’ll get a user manual that explains how to pair and what codes are supported.
If the remote needs to be programmed in the future, keep the user manual on your shelf rather than throwing it away.
Must Read: How To Fix A Remote Control That Got Wet?
Conclusion
You will be able to resolve the errors on your GE universal remote by applying the following troubleshooting methods. In the comment box below, if you have any additional suggestions for fixing this problem, please share them. This will be added to this post, and it will be helpful for others as well.